日本神钢 NO65G*弧焊丝ER70S2进口焊丝
第一枪帮您来“拼单”,更多低价等你来!日本神钢 NO65G*弧焊丝ER70S2进口焊丝
- 名称天津市海焊科技有限公司 【公司网站】
- 所在地中国 天津 武清
- 联系人 李金柱
- 价格 ¥50元/个 点此议价
- 采购量 不限制
- 发布日期 2024-04-29 09:00 至 长期有效
日本神钢 NO65G*弧焊丝ER70S2进口焊丝产品详情
- 规格:2.4
- 品牌:日本神钢
- 类型:实心焊丝
- 焊接方法类型:气焊焊丝
- 型号:日本神钢KOBELCO NO65G氩弧焊丝ER70S-2进口焊丝
- 牌号:日本神钢KOBELCO NO65G氩弧焊丝ER70S-2进口焊丝
日本神钢KOBELCO NO65G*弧焊丝ER70S-2进口焊丝
NO65G TIG rod, equivalent to AWS A5.18 ER70S-2, contains less C, Si and Mn contents than TG-S50 or TG-S51T; instead, Al, Ti and Zr are specially added. These elements help to decrease the amou*f oxygen in the molten pool, allowing NO65G to provide a weld metal of relatively high cleanness. On the other hand, it is a little inferior to TG-S50 or TG-S51T in terms of fluidity of molten metal, because of which its surface tension increases while the oxygen content in the molten metal is decreased.
Because Al, Ti or Zr is an element with high oxygen affinity, slag can be generated on the bead surface after a part of the element combines with oxygen in the molten metal during welding. Users are therefore advised to beware of weld defects, such as poor bead appearance or slag inclusion, caused by the slag.
Each chemical element in NO65G rod is strictly co*olled to maintain a narrow range within the AWS A5.18 ER70S-2 specificati*o that it can meet the tough requirements set out by Japanese clients for mechanical properties in critical structural projects.
Table 8: Typical chemistry of weld metal (mass%)天津海焊C | Si | Mn | P | S | Cu | Al | Ti | Zr |
---|---|---|---|---|---|---|---|---|
0.04 | 0.50 | 1.20 | 0.007 | 0.012 | 0.22 | 0.06 | 0.05 | 0.02 |
Tensile test at RT | Absorbed energy (J) | |||||
---|---|---|---|---|---|---|
YS (MPa) | TS (MPa) | EI (%) | -40°C | -30°C | -20°C | |
As-welded | 584 | 635 | 29 | Av 165 | Av 200 | Av 215 |
625°C × 8hr | 545 | 615 | 30 | Av 138 | Av 160 | Av 175 |
Table 8, Table 9 and Figure 5 show the typical chemistry of NO65G weld metal, the typical mechanical properties in as-welded and PWHT (625°C×8 hr) conditi* and the absorbed energies in relat io*the tes t temperatures, respectively.
Figure 5: Impact properties of weld metal
Figures 6 and 7 show face side bead appearance after root and second passes and back bead appearance after root-pass welding in 1G and 3G (uphill) s by NO65G (2.4m*a.), respectively. Figures 8 and 9 exhibit macro-structures of root-pass and second-pass welding in 1G and 3G (uphill) s, respectively. The groove configuration was of single 60°V, with a root gap of 3.0-3.5mm. The welding conditi* were 110A-12V for root-pass without back-shielding and 160A-13V for second pass welding, respectively.
该公司其他产品
-
昆山京雷GMR-75高强度钢焊丝
¥25.0元/千克 -
美国进口Messer/MG 600 TIG 模具钢合金钢焊丝
¥700.0元/千克 -
天津金桥不锈钢电焊条奥A302不锈钢焊条
¥40.0元/千克 -
金桥JQ HS5356-1铝镁焊丝ER5356弧焊丝
¥40.0元/千克 -
昆山京雷焊丝GFR-81B2V耐热钢气保药芯焊丝
¥39.0元/千克
江湖通产品
- YD888药芯*焊丝 *堆焊焊丝 硬面堆焊焊丝 ¥30.0元/千克
精品推荐
- HS223 RBCuZn-A SCu4700铜焊丝 ¥90.0元/千克
- 瑞典伊萨FILARC PZ6149低合金钢焊丝药芯焊丝 ¥300.0元/件
- 供应上海肯纳司太立Delstain 424H焊丝 面议
- 不锈钢焊丝生产厂家 ¥55.0元/千克
- 供应上海肯纳司太立Multipass 915焊丝 面议