步进电机,奥铭机电****服务(****商家),重庆步进电机厂家
第一枪帮您来“拼单”,更多低价等你来!步进电机,奥铭机电****服务(****商家),重庆步进电机厂家
- 名称东莞市奥铭机电设备有限公司 【公司网站】
- 所在地中国
- 联系人 吴杰
- 价格 面议 点此议价
- 采购量 1
- 发布日期 2016-12-11 16:19 至 长期有效
步进电机,奥铭机电****服务(****商家),重庆步进电机厂家产品详情
<*n style='font-size:24px;'>通电后电机不转有嗡嗡声*n>
<*n style='font-size:16px;'>1、故障原因*n>
<*n style='font-size:16px;'>①转子绕组有断路(一相断线)或电源一相失电;*n>
<*n style='font-size:16px;'>②绕组引出线始末端接错或绕组内部接反;*n>
<*n style='font-size:16px;'>③电源回路接点松动,接触电阻大;*n>
<*n style='font-size:16px;'>④电动机负载过大或转子卡住;*n>
<*n style='font-size:16px;'>⑤电源电压过低;*n>
<*n style='font-size:16px;'>⑥小型电动机装配太紧或轴承内油脂过硬;*n>
<*n style='font-size:16px;'>⑦轴承卡住。*n>
<*n style='font-size:16px;'>2、故障排除*n>
<*n style='font-size:16px;'>①查明断点予以*;*n>
<*n style='font-size:16px;'>②检查绕组****性;判断绕组末端是否正确;*n>
<*n style='font-size:16px;'>③紧固松动的接线螺丝,用万用表判断各接头是否假接,予以*;*n>
<*n style='font-size:16px;'>④减载或查出并消除机械故障,*n>
<*n style='font-size:16px;'>⑤检查是否把规定的面接法误接;是否由于电源导线过细使压降过大,予以纠正,*n>
<*n style='font-size:16px;'>⑥重新装配使之灵活;更换合格油脂;*n>
<*n style='font-size:16px;'>⑦*轴承。*n>
<*n style='font-size:16px;'><*n style='color:#006600;'>*n><*n style='font-size:24px;'><*n style='color:#006600;'>电动机*n><*n style='color:#006600;'>运行时响声不正常有异响*n>*n>*n>
<*n style='font-size:16px;'>1、故障原因*n>
<*n style='font-size:16px;'>①轴承磨损或油内有砂粒等*;*n>
<*n style='font-size:16px;'>②转子铁芯松动;*n>
<*n style='font-size:16px;'>③轴承缺油;*n>
<*n style='font-size:16px;'>④电源电压过高或不平衡。 *n>
<*n style='font-size:16px;'>2、故障排除*n>
<*n style='font-size:16px;'>①更换轴承或清洗轴承;*n>
<*n style='font-size:16px;'>②检修转子铁芯;*n>
<*n style='font-size:16px;'>③加油;*n>
<*n style='font-size:16px;'>④检查并调整电源电压*n>
<*n style='font-size:16px;'>5、电动机起动困难,额定负载时,电动机转速低于额定转速较多*n>
<*n style='font-size:16px;'>1、故障原因*n>
<*n style='font-size:16px;'>①电源电压过低;*n>
<*n style='font-size:16px;'>②面接法电机误接;*n>
<*n style='font-size:16px;'>③转子开焊或断裂;*n>
<*n style='font-size:16px;'>④转子局部线圈错接、接反;*n>
<*n style='font-size:16px;'>③*电机绕组时增加匝数过多;*n>
<*n style='font-size:16px;'>⑤电机过载。 *n>
<*n style='font-size:16px;'>2、故障排除*n>
<*n style='font-size:16px;'>①测量电源电压,设法****;*n>
<*n style='font-size:16px;'>②纠正接法;*n>
<*n style='font-size:16px;'>③检查开焊和断点并*;*n>
<*n style='font-size:16px;'>④查出误接处予以改正;*n>
<*n style='font-size:16px;'>⑤恢复正确匝数;*n>
<*n style='font-size:16px;'>⑥减载。*n>
<*n style='font-size:16px;'>6、通电后电动机不能转动,但无异响,也无异味和冒烟?*n>
<*n style='font-size:16px;'>1、故障原因*n>
<*n style='font-size:16px;'>①电源未通(至少两相未通);*n>
<*n style='font-size:16px;'>②熔丝熔断(至少两相熔断);*n>
<*n style='font-size:16px;'>③过流继电器调得过小;*n>
<*n style='font-size:16px;'>④控制设备接线错误。*n>
<*n style='font-size:16px;'>2、故障排除*n>
<*n style='font-size:16px;'>①检查电源回路开关,熔丝、接线盒处是否有断点,*;*n>
<*n style='font-size:16px;'>②检查熔丝型号、熔断原因,换新熔丝;*n>
<*n style='font-size:16px;'>③调节继电器整定值与电动机配合;*n>
<*n style='font-size:16px;'>④改正接线。*n>
<*n style='font-size:16px;'>7、运行中电动机振动较大*n>
<*n style='font-size:16px;'>1、故障原因*n>
<*n style='font-size:16px;'>①由于磨损轴承间隙过大;*n>
<*n style='font-size:16px;'>②气隙不均匀;*n>
<*n style='font-size:16px;'>③转子不平衡;*n>
<*n style='font-size:16px;'>④转轴弯曲;*n>
<*n style='font-size:16px;'>⑤联轴器(皮带轮)同轴度过低。 *n>
<*n style='font-size:16px;'>2、故障排除*n>
<*n style='font-size:16px;'>①检修轴承,必要时更换;*n>
<*n style='font-size:16px;'>②调整气隙,使之均匀;*n>
<*n style='font-size:
该公司其他产品
江湖通产品
- 电动机 电机 微型电机 汽车用电机 ¥1.0元/件